Exfo FTB/IQS-88000 Series Power Blazer for FTB-2/2Pro/5 Manual de usuario descargar pdf (Pagina 562)

100

101

Specifications

550 FTB/IQS-88000 Series

Synchronization Interface

For 88100NGE, 88100G and 8830NGE:

a. An SMB to BNC adapter is available.

For 8805:

External Clock DS1/1.5M External Clock E1/2M 2 MHz

Tx pulse amplitude (V) 2.4 to 3.6 2.37 0.75 to 1.5

Tx pulse mask GR-499 figure 9.5 G.703 figure 15 G.703 figure 20

Tx LBO pre-amplification

(typical) (dBdsx)

0.6 for 0 to 40.5 m (0 to 133 ft)

1.2 for 40.5 to 81.1 m (133 to 266 ft)

1.8 for 81.1 to 121.6 m (266 to 399 ft)

2.4 for 121.6 to 162.5 m (399 to 533 ft)

3.0 for 162.5 to 200 m (533 to 655 ft)

Rx level sensitivity

TERM: )6 dB (cable loss only)

(at 772 kHz for T1)

DSX-MON: )26 dB (20 dB

resistive loss + cable loss ) 6 dB)

TERM: )6 dB (cable loss only)

MON: )26 dB (resistive loss

+ cable loss ) 6 dB)

)6 dB (cable loss only)

Transmission bit rate 1.544 Mbit/s ± 4.6 ppm 2.048 Mbit/s ± 4.6 ppm

Reception bit rate 1.544 Mbit/s ± 50 ppm 2.048 Mbit/s ± 50 ppm

Intrinsic jitter (Tx) ANSI T1.403 section 6.3

GR-499 section 7.3

G.823 section 6.1 G.703 table 11

Input jitter tolerance AT&T PUB 62411

GR-499 SECTION 7.3

G.823 section 7.2

G.813

Line coding AMI and B8ZS AMI and HDB3

Input impedance

(resistive termination)

75  ± 5 %, unbalanced 75  ± 5 %, unbalanced 75  ± 5 %, unbalanced

Connector type

SMB SMB SMB

External Clock DS1/1.5M External Clock E1/2M External Clock E1/2M Trigger 2 MHz

Tx pulse amplitude 2.4 to 3.6 V 3.0 V 2.37 V 0.75 to 1.5 V

Tx pulse mask GR-499 Figure 9.5G.703 Figure 15 G.703 Figure 15 G.703 Figure 20

Tx LBO preamplification Typical power dBdsx

+0.6 dBdsx (0-133 ft)

+1.2 dBdsx (133-266 ft)

+1.8 dBdsx (266-399 ft)

+2.4 dBdsx (399-533 ft)

+3.0 dBdsx (533-655 ft)

Rx level sensitivity

TERM: )6 dB (cable loss only)

(at 772 kHz for T1)

DSX-MON: )26 dB (20 dB resistive

loss + cable loss ) 6 dB)

Bridge: )6 dB (cable loss only)

TERM: )6 dB (cable loss only)

MON:

)26 dB (20 dB resistive loss

+ cable loss ) 6 dB)

Bridge: )6 dB (cable loss only)

TERM: )6 dB (cable loss only)

MON: )26 dB (resistive loss

+ cable loss ) 6 dB)

Bridge: )6 dB (cable loss only)

)6 dB (cable loss only)

Transmission bit rate 1.544 Mbit/s ± 4.6 ppm 2.048 Mbit/s ± 4.6 ppm 2.048 Mbit/s ± 4.6 ppm

Reception bit rate 1.544 Mbit/s ± 50 ppm 2.048 Mbit/s ± 50 ppm 2.048 Mbit/s ± 50 ppm

Intrinsic jitter (Tx)

ANSI T1.403 section 6.3

GR-499 section 7

G.823 section 6.1G.823 section 6.1G.703 table 11

Input jitter tolerance AT&T PUB 62411

GR-499 section 7.3

G.823 section 7.2

G.813

G.823 section 7.2

G.813

G.823 section 7.1

G.751 section 3.3

Line coding AMI and B8ZS AMI and HDB3 AMI and HDB3

Input impedance (resistive termination) 75 ohms ± 5 %, unbalanced 75 ohms ± 5 %, unbalanced 75 ohms ± 5 %, unbalanced 75 ohms ± 5 %, unbalanced

Connector type BNC

BNC

BNC BNC

Note

a. Adaptation cable required for BANTAM.

1 2 ... 557 558 559 560 561 562 563 564 565 566 567 ... 680 681

Comentarios a estos manuales

Sin comentarios

Exfo FTB/IQS-88000 Series Power Blazer for FTB-2/2Pro/5 Manual de usuario Pagina 562

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos de medición Exfo FTB/IQS-88000 Series Power Blazer for FTB-2/2Pro/5