Exfo FTB/IQS-88000 Series Power Blazer for FTB-2/2Pro/5 Manual de usuario Pagina 295
- Pagina / 681
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Test Results
Power Blazer 283
Alarms/Errors
ODUx
Note: For OPUx alarms see page 288.For GMP alarms/errors see page 278.
Alarms
AIS (Alarm Indication Signal)
RX: The STAT information in the PM byte 3, bits 6 to 8 is “111” for at
least 3 consecutive frames.
TX: Generates an all "1"s pattern in the entire ODUk signal, excluding
the frame alignment overhead (FA OH), OTUk overhead (OTUk OH)
and ODUk FTFL.
BDI (Backward Defect indication)
RX: The BDI bit in the PM overhead field (byte 3, bit 5) is “1” for at least
5 consecutive frames.
TX: Generates a “1” in the BDI (byte 3, bit 5) of the PM overhead field
continuously.
BSD (Backward Signal Degrade)
RX: The FTFL byte 128 is “00000010”.
TX: Generates a “00000010” pattern in the FTFL Byte 128 continuously.
BSF (Backward Signal Fail)
RX: The FTFL byte 128 is “00000001”.
TX: Generates a “00000001” pattern in the FTFL Byte 128 continuously.
FSD (Forward Signal Degrade)
RX: The FTFL byte 0 is “00000010”
TX: Generates a “00000010” pattern in the FTFL Byte 0 continuously.
- FTB/IQS-88000 Series 1
- Certification Information 3
- Contents 5
- Power Blazer vii 7
- Power Blazer ix 9
- Power Blazer xi 11
- 1 Introducing the High-Speed 13
- Multiservice Test Module 13
- IMPORTANT 14
- 2 Safety Information 15
- 4 FTB/IQS-88000 Series 16
- Power Blazer 5 17
- 6 FTB/IQS-88000 Series 18
- 3 Getting Started 19
- Turning On the Unit 21
- Physical Interfaces and LEDs 24
- FTB-8805/IQS-8805 25
- CFP Interface 28
- CFP Transceiver 29
- EXFO CFP-to-CFP2 Adapter 29
- SFP/SFP+ (PORT #1/#2) 30
- Application Rates 31
- BNC (PORT #1 on FTB/IQS-8805) 32
- AUX (PORT #2 on FTB/IQS-8805) 32
- Fibre Cables Connection 33
- EXT CLK 33
- 5 Graphical User Interface 35
- Overview 35
- Status Bar 36
- Title Bar 37
- Test Control 38
- Test Menu 38
- Application Buttons 38
- Software Option Description 39
- 28 FTB/IQS-88000 Series 40
- Keyboard Usage 41
- 30 FTB/IQS-88000 Series 42
- ITU T.50 Characters 43
- OTN BERT 46
- Path/Mapping 47
- OTN-SONET/SDH BERT 48
- Path/Mapping 49
- For OTN-SDH BERT 50
- SONET/SDH BERT 51
- 40 FTB/IQS-88000 Series 52
- For SDH BERT 53
- DSn/PDH BERT 54
- NI/CSU Emulation 56
- EtherSAM (Y.1564) 57
- 46 FTB/IQS-88000 Series 58
- RFC 2544 59
- 48 FTB/IQS-88000 Series 60
- EtherBERT 61
- Traffic Gen & Mon 62
- Third-Party Remote Loopback 64
- Through Mode 65
- Carrier Ethernet OAM 67
- 58 FTB/IQS-88000 Series 70
- FC BERT 71
- Transport Test Applications 73
- 62 FTB/IQS-88000 Series 74
- 64 FTB/IQS-88000 Series 76
- Packet Sync Test Applications 77
- 66 FTB/IQS-88000 Series 78
- 68 FTB/IQS-88000 Series 80
- Timer, and System 81
- 70 FTB/IQS-88000 Series 82
- Block Subtab or Pop Up 82
- Test Application 82
- Timer, see page 241 83
- System, see page 238 83
- Test Configurator Overview 84
- Ethernet Test Applications: 85
- 74 FTB/IQS-88000 Series 86
- Icon Description 87
- 78 FTB/IQS-88000 Series 90
- Test Interface/Rate 90
- Interface/Rate Connector 91
- 80 FTB/IQS-88000 Series 92
- 82 FTB/IQS-88000 Series 94
- 84 FTB/IQS-88000 Series 96
- 86 FTB/IQS-88000 Series 98
- Power Blazer 87 99
- 88 FTB/IQS-88000 Series 100
- Modify Structure Button 100
- FTB-800v2 Series 102
- 92 FTB/IQS-88000 Series 104
- Loopback Mode 105
- OAM Type 105
- Signal Auto-Detect 108
- 1588 PTP 109
- PTSF Alarm Timeout/Threshold 112
- Quality Level 112
- Pass/Fail Verdict 113
- Restore 1588 PTP Defaults 113
- BERT and Unframed BERT 114
- OTN and SONET/SDH Interfaces: 115
- 104 FTB/IQS-88000 Series 116
- Bit Error 117
- Service Disruption 118
- Power Blazer 107 119
- Multi-Pattern Configuration 120
- Cable Test 121
- CFP/CFP2/XFP/SFP/SFP+ 123
- Clock Synchronization 124
- Ext Clock In 124
- Power Blazer 113 125
- Ext Clock Out 126
- REF OUT 127
- Backplane 127
- Pattern 128
- Bit/Pattern Error 129
- FC Frame 130
- Latency Tag Insertion 131
- Ethernet Frame 132
- Power Blazer 121 133
- EtherSAM - Burst 134
- Parameters 135
- EtherSAM - Global 136
- Subtests 137
- 126 FTB/IQS-88000 Series 138
- Global Options 139
- Restore EtherSAM Defaults 139
- EtherSAM - Ramp 140
- Delete Step 141
- Defaults 141
- Fibre Channel 142
- Power Blazer 131 143
- Frequency 145
- RX Frequency 146
- ODUx Buttons 147
- GFP-F/GFP-T 150
- Channel) 151
- WIS Button 153
- Physical Interface 154
- Power Blazer 143 155
- TX Frequency 156
- Power Blazer 147 159
- MAC/IP/UDP 160
- Modify Frame Structure 161
- Preamble/SFD 162
- Flood Range 163
- Power Blazer 157 169
- Power Blazer 159 171
- 160 FTB/IQS-88000 Series 172
- DSCP Codepoints: 172
- Power Blazer 161 173
- Network 174
- Power Blazer 163 175
- Power Blazer 165 177
- RFC 2544 - Global 179
- Subtests and Estimated Time 180
- Frame Distribution 181
- Restore RFC 2544 Defaults 181
- RFC 2544 - Subtests 182
- Back-to-Back 185
- Frame Loss Configuration 186
- Latency Configuration 187
- 176 FTB/IQS-88000 Series 188
- Thresholds Button 189
- S-OAM and MPLS-TP OAM 191
- 180 FTB/IQS-88000 Series 192
- Thresholds 193
- Next HOP Router (G.8113.1) 194
- Local Parameters 194
- Peer MEP Parameters 195
- Continuity Check 195
- Test Function 197
- Services - Global 201
- SLA Button 202
- Total TX Rate 203
- Copy Service Button 203
- Services - Profile 204
- Profile 205
- Component Description 207
- Test Parameters 208
- SLA Parameters 209
- Signal (Transport) 211
- Signal LBO 213
- Signal Configuration 217
- 206 FTB/IQS-88000 Series 218
- DS1 DS3 E1 E3/E4 218
- Background 219
- Channel 219
- Modify DS0/E0 220
- Power Blazer 209 221
- 210 FTB/IQS-88000 Series 222
- Loopback button 223
- 212 FTB/IQS-88000 Series 224
- Modify Loop Codes button 224
- Power Blazer 215 227
- OC/STM Signal 231
- STS/AU and VT/TU Mappings 232
- Power Blazer 221 233
- STS-1, AU-3, and AU-4 234
- Power Blazer 223 235
- Smart Loopback 236
- S-OAM Responder 237
- Streams - Global 238
- Power Blazer 227 239
- Streams - Profile 240
- Power Blazer 229 241
- Shaping 244
- Power Blazer 233 245
- QoS Metrics 246
- Power Blazer 235 247
- ESMC Monitoring 248
- ESMC Generation 249
- Restore SyncE Defaults 249
- Factory Default 250
- Remote Control 250
- TCP Throughput 251
- TCP Throughput Configuration 252
- Power Blazer 241 253
- 242 FTB/IQS-88000 Series 254
- Traces (OTN) 255
- Traces (SONET/SDH) 258
- TCM Access Point Identifier 259
- 9Test Results 261
- Test Results 262
- Ethernet Test Applications 262
- Alarms/Errors Overview 264
- Statistic Values 265
- P1 and P2 Buttons 265
- Alarms/Errors 266
- No Traffic 269
- Pattern Loss 269
- LOC (Loss Of Clock) 271
- Power Blazer 261 273
- Power Blazer 263 275
- Power Blazer 265 277
- Ethernet 278
- Ethernet - PCS Lanes 281
- Power Blazer 273 285
- Power Blazer 275 287
- 278 FTB/IQS-88000 Series 290
- Cm-CRC-8 290
- CnD-CRC-5 290
- Interface 291
- For serial interfaces: 292
- Power Blazer 281 293
- IP/UDP/TCP 294
- Power Blazer 283 295
- ODUx-TCM 298
- Power Blazer 289 301
- Power Blazer 291 303
- Unexp MEP (Unexpected MEP) 309
- Section/Line / RS/MS 312
- Power Blazer 301 313
- STS-x/AU-x 314
- Power Blazer 303 315
- 304 FTB/IQS-88000 Series 316
- ESMC Loss 317
- TCM (SONET/SDH) 318
- Power Blazer 307 319
- Transcoding 321
- Power Blazer 311 323
- Power Blazer 313 325
- Power Blazer 315 327
- 316 FTB/IQS-88000 Series 328
- Inject Button 329
- Power Blazer 319 331
- 320 FTB/IQS-88000 Series 332
- Inject button 332
- PT (Payload Type) 334
- RX Mismatch 336
- Superblock 337
- Graph (RFC 2544) 338
- Power Blazer 327 339
- Sort By 340
- Label 1 and Label 2 342
- Total TX/RX MPLS 342
- 332 FTB/IQS-88000 Series 344
- Performance Monitoring 345
- Near-End 346
- Signal SES Threshold 347
- Far-End 349
- 338 FTB/IQS-88000 Series 350
- Power Blazer 339 351
- PTP Stats 352
- Quality Level (1588 PTP) 354
- Quality Level (SyncE) 356
- Frame Delay 361
- Frame Loss 362
- Synthetic Loss 363
- Service Name and Selection 364
- Committed/Excess 364
- Service Configuration - Ramp 365
- 354 FTB/IQS-88000 Series 366
- Service Performance 367
- RX Frame Count 368
- Streams - Jitter 369
- Streams - Latency 370
- Streams - Throughput 371
- Summary 372
- BER and Multi-Pattern BER 373
- GFP Frames 375
- Traffic / Traffic Ethernet 375
- Summary (1588 PTP) 377
- Negotiation Status 378
- Delay Measurement 380
- Total PTP Messages 380
- Summary (Cable Test) 381
- 372 FTB/IQS-88000 Series 384
- Summary (EtherSAM) 385
- Power Blazer 375 387
- Summary (FC BERT) 388
- Power Blazer 377 389
- Round-Trip Latency 390
- Traffic 390
- Summary (NI/CSU Emulation) 391
- Summary (RFC 2544) 392
- Latency Subtests 393
- Continuity Check (Peer MEP) 396
- Supported Format 397
- Summary (SyncE) 400
- Summary (TCP Throughput) 403
- Ethernet Traffic 405
- Power Blazer 395 407
- Traces - OTN 408
- Traces - SONET/SDH 410
- Traffic - Ethernet 411
- Frame Size 412
- Traffic - Flow Control 413
- Pause Injection 414
- Traffic - Graph 415
- Traffic Monitoring 416
- Responder 417
- Traces/Label 418
- 10 Test Functions 419
- Test Functions 420
- CFP/CFP2 Power Class 421
- CFP/CFP2 Control Pins 421
- CFP/CFP2 Status Pins 422
- CFP/CFP2 TX Status 423
- CAUI/Physical Lane 424
- PCS/Logical Lane 425
- Default/Random/Manual Mapping 426
- Reset/Manual Skew 427
- Laser ON/OFF 428
- Skew Alarm Threshold (bits) 428
- Power Blazer 417 429
- 418 FTB/IQS-88000 Series 430
- Client Offset 434
- 424 FTB/IQS-88000 Series 436
- FDL - Bit-Oriented Message 437
- Codeword 438
- Receive Messages 439
- 428 FTB/IQS-88000 Series 440
- Command/Response 440
- Generated Messages 441
- Received Messages 442
- Power Blazer 431 443
- Loopback Commands 447
- Filters 448
- Assign to Capture 449
- Filter Configuration 449
- Filter Statistics 451
- Packet Capture 452
- Frame Length 453
- Status and Controls 455
- Generate & Save 457
- Generic Mapping Procedure 458
- OH - GFP-F/GFP-T 459
- Header Identifier 460
- Identifier 460
- Default all OH 461
- OH Details 463
- OH - OTN 464
- Power Blazer 453 465
- BEI/BIAE BDI IAE RES 465
- BEI/BIAE BDI STAT 466
- Power Blazer 455 467
- BEI BDI STAT 467
- Power Blazer 457 469
- OH - SONET/SDH 470
- Transport OH - Section/RS 471
- Transport OH - Line/MS 472
- STS/AU/TU-3 478
- Power Blazer 469 481
- Disable all Overwrites 484
- Ping & Trace Route 485
- Use Stream 486
- Trace Route 487
- Power Blazer 477 489
- Pointer Adjustment 490
- 480 FTB/IQS-88000 Series 492
- Description 493
- 484 FTB/IQS-88000 Series 496
- Power Blazer 485 497
- 486 FTB/IQS-88000 Series 498
- RX Pointer Adjustment 499
- 488 FTB/IQS-88000 Series 500
- Measure Delay Button 501
- S-OAM Link Trace 503
- 492 FTB/IQS-88000 Series 504
- Signaling Bits 505
- Spare Bits 506
- Power Blazer 495 507
- 11 Test Control 509
- Discover Remote Button 510
- Local Module Identification 512
- Laser Button 513
- 502 FTB/IQS-88000 Series 514
- Loopback Tool tab 515
- 1. Refer to 517
- Interface Tab 518
- Power Blazer 507 519
- Network tab 520
- SFP/SFP+ tab 520
- Report Button 521
- Open Tab 523
- Import/Export Tab 524
- Reset Button 525
- Save/Load Button 526
- 516 FTB/IQS-88000 Series 528
- Start/Stop 532
- 12 Power Failure Recovery 533
- 522 FTB/IQS-88000 Series 534
- When Using the Test Timer 535
- 13 Suspend and Resume 537
- Resume Operation 538
- 14 Maintenance 539
- 528 FTB/IQS-88000 Series 540
- Recalibrating the Unit 541
- Recycling and Disposal 542
- 15 Troubleshooting 543
- Transportation 544
- 16 Warranty 545
- Service and Repairs 547
- 536 FTB/IQS-88000 Series 548
- ASpecifications 549
- Specifications 550
- Interfaces 555
- Synchronization Interface 562
- B Glossary 565
- 554 FTB/IQS-88000 Series 566
- Acronym List 566
- 556 FTB/IQS-88000 Series 568
- 558 FTB/IQS-88000 Series 570
- 560 FTB/IQS-88000 Series 572
- 562 FTB/IQS-88000 Series 574
- 564 FTB/IQS-88000 Series 576
- 566 FTB/IQS-88000 Series 578
- 568 FTB/IQS-88000 Series 580
- 10G Ethernet Client 582
- Glossary 583
- 572 FTB/IQS-88000 Series 584
- 1588 PTP Profiles 587
- 576 FTB/IQS-88000 Series 588
- Ethernet Cables 590
- (ex: router) 591
- Crossover Cable (1000 Mbit/s) 592
- 582 FTB/IQS-88000 Series 594
- Power Blazer 583 595
- Power Blazer 585 597
- 586 FTB/IQS-88000 Series 598
- Framing 598
- OTU FEC 598
- Overhead 599
- 588 FTB/IQS-88000 Series 600
- Optical Data Unit (ODU) 601
- 590 FTB/IQS-88000 Series 602
- Optical Payload Unit (OPU) 602
- Power Blazer 591 603
- Tandem Connection Monitoring 603
- 592 FTB/IQS-88000 Series 604
- Power Blazer 593 605
- Forward Error Correction 605
- ODU Multiplexing 606
- Power Blazer 595 607
- ODUflex 608
- OTN Signal Rates 609
- 598 FTB/IQS-88000 Series 610
- Power Blazer 599 611
- GFP Mapping 612
- GFP Frame Structure 614
- Power Blazer 603 615
- GFP Generic Frame Structure 615
- 000 Client Data Frame 616
- 100 Client Management Frame 616
- Others Reserved 616
- Power Blazer 607 619
- 608 FTB/IQS-88000 Series 620
- Payload Information Field 620
- Payload FCS (pFCS) 620
- GFP Summary 621
- MPLS Labels 622
- SONET/DSn/SDH/PDH 623
- Nomenclature 624
- SONET Numbering Convention 627
- SDH Numbering Convention 628
- Power Blazer 617 629
- 618 FTB/IQS-88000 Series 630
- DSn/PDH Numbering Convention 632
- Power Blazer 621 633
- 622 FTB/IQS-88000 Series 634
- VLAN ID and Priority 636
- C Remote ToolBox 637
- Remote ToolBox Installation 639
- Application 640
- Modules 641
- Applications for 642
- Power Blazer 631 643
- Power Blazer 633 645
- Power Blazer 635 647
- Power Blazer 637 649
- Power Blazer 639 651
- Power Blazer 641 653
- Power Blazer 643 655
- Power Blazer 645 657
- Power Blazer 647 659
- Power Blazer 649 661
- Power Blazer 651 663
- Power Blazer 653 665
- Power Blazer 655 667
- Power Blazer 657 669
- Power Blazer 659 671
- Power Blazer 661 673
- Power Blazer 663 675
- Power Blazer 665 677
- ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ 679
- MARKING REQUIREMENTS 680
Relacionado con productos y manuales para Instrumentos de medición Exfo FTB/IQS-88000 Series Power Blazer for FTB-2/2Pro/5
Instrumentos de medición Exfo FastReporter Data Post-Processing Software Manual de usuario
(256 paginas)
(256 paginas)
Instrumentos de medición Exfo FastReporter Data Post-Processing Software Manual de usuario
(270 paginas)
(270 paginas)
Instrumentos de medición Exfo FastReporter Data Post-Processing Software Manual de usuario
(274 paginas)
(274 paginas)
Instrumentos de medición Exfo MAX-700 Manual de usuario
(381 paginas)
(381 paginas)
Instrumentos de medición Exfo MAX-700 Manual de usuario
(418 paginas)
(418 paginas)
Instrumentos de medición Exfo MAX-700 Manual de usuario
(414 paginas)
(414 paginas)
Instrumentos de medición Exfo MAX-700 Manual de usuario
(422 paginas)
(422 paginas)
Instrumentos de medición Exfo MAX-700 Manual de usuario
(414 paginas)
(414 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.064 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales