Exfo FTB-800 Series for FTB-1 Manual de usuario Pagina 419
- Pagina / 621
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Test Functions
NetBlazer 409
Filters and Packet Capture - Filters
Mask allows masking the defined filter value. A bit mask of 1
indicates that the corresponding bit in the value is compared for
the match. A bit mask of 0 indicates that the corresponding bit in
the value is ignored.
For binary values, enter the mask value in binary format.
For decimal values, enter the mask value in hexadecimal format.
For IP address field, enter the mask in decimal format.
For MAC address, enter the mask value in hexadecimal format.
Oper. specifies the logical operator (AND or OR) used between
two operands.
Filter Statistics
Indicates throughput statistics of frame matching the configured filter’s
criteria.
Line Utilization gives the percentage of line rate utilization.
Ethernet BW (Bandwidth) gives the receiving data rate expressed in
Mbit/s.
Frame Rate gives the receiving number of frames (including bad
frames) in frame/s.
Frame Count indicates the number of frame matching the configured
filter’s criteria.
Error Count indicates respectively the number of frames matching the
configured filter’s criteria having IP Checksum, UDP Checksum,
TCP Checksum, FCS, Jabber, Oversize, Runt, or Undersize errors.
Refer to Ethernet on page 257 and IP/UDP/TCP on page 263 for more
information on errors.
- FTB-700G/800 Series 1
- Certification Information 3
- Contents 5
- NetBlazer vii 7
- NetBlazer ix 9
- Multiservice Tester 11
- IMPORTANT 12
- 2 Safety Information 13
- 4 FTB-700G/800 Series 14
- 6 FTB-700G/800 Series 16
- 3 Getting Started 17
- FTB-810 and FTB-810G Modules 19
- Physical Interfaces and LEDs 20
- FTB-860G Module 21
- FTB-860GL Module 21
- FTB-870, FTB-720G 22
- , and FTB-730G 22
- Modules 22
- FTB-880 Module 23
- 14 FTB-700G/800 Series 24
- 100M-4.25G (PORT #1/#2) 26
- 8.5G-11.3G (PORT #1) 27
- 155M-2.5G (PORT #1) 28
- 10G (PORT #1) 29
- ETHERNET 10G (PORT #1) 30
- NetBlazer 21 31
- ETHERNET 10/100/1000M 32
- 2M-155M (PORT #1) 32
- 2M-52M (PORT #2) 32
- 1.5M/2M (PORT #1/#2) 32
- AUX Connection 33
- Fibre Cables Connection 33
- EXT CLK 34
- 5 Graphical User Interface 35
- Overview 35
- Status Bar 36
- NetBlazer 27 37
- Title Bar 38
- Global Indicator 39
- Global Verdict 40
- Global Alarm 41
- Test Control 42
- Test Menu 42
- Application Buttons 42
- Options Description 43
- 34 FTB-700G/800 Series 44
- Zoomed-In/Zoomed-Out Views 45
- Arrow Buttons 45
- Keyboard Usage 46
- 38 FTB-700G/800 Series 48
- ITU T.50 Characters 48
- OTN BERT 50
- Path/Mapping 51
- SONET/SDH BERT 52
- Path/Mapping 53
- For SDH BERT 54
- DSn/PDH BERT 55
- 46 FTB-700G/800 Series 56
- SONET/SDH - DSn/PDH BERT 57
- 48 FTB-700G/800 Series 58
- For SDH: 59
- NI/CSU Emulation 60
- ISDN PRI 61
- EtherSAM (Y.1564) 62
- RFC 2544 63
- EtherBERT 64
- Traffic Gen & Mon 65
- Third-Party Remote Loopback 67
- Through Mode 68
- Carrier Ethernet OAM 70
- FTB-700G/800 Series EEC 73
- FC BERT 74
- CPRI/OBSAI BERT 75
- Transport Test Applications 77
- 68 FTB-700G/800 Series 78
- 70 FTB-700G/800 Series 80
- Packet Sync Test Applications 81
- 72 FTB-700G/800 Series 82
- NetBlazer 73 83
- Timer, and System 87
- 78 FTB-700G/800 Series 88
- Block Subtab or Pop Up 88
- Test Application 88
- Timer, see page 234 90
- System, see page 231 90
- Test Configurator Overview 91
- Ethernet Test Applications: 92
- Wireless Test Application: 92
- NetBlazer 83 93
- NetBlazer 87 97
- NetBlazer 89 99
- 90 FTB-700G/800 Series 100
- Modify Structure Button 100
- Test Interface/Rate 100
- Interface/Rate Connector 101
- These patterns are 102
- Loopback Mode 103
- Signal Auto-Detect 105
- 1588 PTP 106
- NetBlazer 97 107
- PTSF Alarm Timeout/Threshold 109
- Quality Level 109
- Pass/Fail Verdict 110
- Restore 1588 PTP Defaults 110
- NetBlazer 101 111
- 102 FTB-700G/800 Series 112
- Bit Error 113
- Service Disruption 113
- 104 FTB-700G/800 Series 114
- Layer Signal Defect 114
- NetBlazer 105 115
- Multi-Pattern Configuration 116
- Cable Test 117
- SFP/SFP+ 119
- Clock Synchronization 120
- Ext Clock In 120
- NetBlazer 111 121
- Ext Clock Out 122
- NetBlazer 113 123
- EtherBERT and Unframed BERT 124
- Bit/Pattern Error 125
- Ethernet Frame 127
- EtherSAM - Burst 128
- Parameters 129
- EtherSAM - Global 130
- Subtests 131
- 122 FTB-700G/800 Series 132
- Global Options 133
- Restore EtherSAM Defaults 133
- EtherSAM - Ramp 134
- Delete Step 135
- Defaults 135
- Payload Type and Code 137
- Global (Fibre Channel) 140
- Round-Trip Latency 141
- Test Timer 142
- Interface (Ethernet) 143
- 134 FTB-700G/800 Series 144
- WIS Button 145
- Physical Interface 146
- TX Frequency 147
- RX Frequency 148
- World Wide Name (WWN) 149
- Buffer to Buffer Flow Control 150
- NetBlazer 141 151
- ISDN PRI - Call Management 153
- Answer Mode 155
- Call Control 156
- ISDN PRI - ISDN Settings 158
- Restore ISDN PRI Defaults 159
- MAC/IP/UDP 161
- Modify Frame Structure 162
- Preamble/SFD 163
- NetBlazer 159 169
- NetBlazer 161 171
- 162 FTB-700G/800 Series 172
- DSCP Codepoints: 172
- NetBlazer 163 173
- Network 174
- NetBlazer 165 175
- NetBlazer 167 177
- RFC 2544 - Global 179
- Subtests and Estimated Time 180
- Frame Distribution 180
- Restore RFC 2544 Defaults 181
- RFC 2544 - Subtests 182
- Back-to-Back 185
- Frame Loss Configuration 186
- Latency Configuration 187
- 178 FTB-700G/800 Series 188
- Thresholds Button 189
- 180 FTB-700G/800 Series 190
- S-OAM Mode 191
- S-OAM Responder 191
- Thresholds 192
- Local Parameters 193
- Peer MEP Parameters 193
- Continuity Check 194
- Test Function 194
- NetBlazer 185 195
- NetBlazer 187 197
- Services - Global 198
- SLA Button 199
- Total TX Rate 199
- Copy Service Button 200
- Services - Profile 201
- Profile 202
- 194 FTB-700G/800 Series 204
- Component Description 204
- Test Parameters 205
- SLA Parameters 206
- NetBlazer 197 207
- Signal (Transport) 208
- Signal LBO 209
- Signal Configuration 213
- Background 214
- Channel 215
- Modify DS0/E0 215
- 206 FTB-700G/800 Series 216
- NetBlazer 207 217
- Loopback button 218
- Modify Loop Codes button 219
- NetBlazer 211 221
- 212 FTB-700G/800 Series 222
- NetBlazer 213 223
- OC/STM Signal 224
- STS/AU and VT/TU Mappings 225
- 216 FTB-700G/800 Series 226
- NetBlazer 217 227
- Smart Loopback 228
- Streams - Global 230
- NetBlazer 221 231
- Streams - Profile 232
- NetBlazer 223 233
- Shaping 235
- QoS Metrics 237
- ESMC Monitoring 239
- ESMC Generation 240
- Restore SyncE Defaults 240
- Factory Default 241
- Remote Control 241
- TCP Throughput 242
- TCP Throughput Configuration 243
- 234 FTB-700G/800 Series 244
- NetBlazer 235 245
- Traces (OTN) 246
- NetBlazer 237 247
- 238 FTB-700G/800 Series 248
- Traces (SONET/SDH) 249
- TCM Access Point Identifier 250
- 9Test Results 251
- Test Results 252
- Ethernet Test Applications 252
- Wireless Test Application 253
- Alarms/Errors Overview 254
- Statistic Values 255
- Alarms/Errors 256
- NetBlazer 249 259
- 250 FTB-700G/800 Series 260
- LOC (Loss Of Clock) 260
- NetBlazer 251 261
- NetBlazer 253 263
- NetBlazer 255 265
- Ethernet 267
- NetBlazer 259 269
- Fibre Channel 270
- Interface 271
- IP/UDP/TCP 273
- NetBlazer 265 275
- ODUx-TCM 277
- CSF (Client Signal Fail) 279
- NetBlazer 271 281
- NetBlazer 277 287
- Section/Line / RS/MS 289
- STS-x/AU-x 291
- 284 FTB-700G/800 Series 294
- ESMC Loss 294
- TCM (SONET/SDH) 295
- NetBlazer 287 297
- NetBlazer 289 299
- NetBlazer 291 301
- NetBlazer 293 303
- 294 FTB-700G/800 Series 304
- Inject Button 305
- Inject button 307
- PT (Payload Type) 309
- Graph (RFC 2544) 310
- ISDN Logger 311
- NetBlazer 303 313
- NetBlazer 305 315
- Sort By 317
- Label 1 and Label 2 319
- Total TX/RX MPLS 319
- Performance Monitoring 320
- Near-End 321
- 312 FTB-700G/800 Series 322
- Signal SES Threshold 322
- NetBlazer 313 323
- Far-End 324
- PTP Stats 327
- 318 FTB-700G/800 Series 328
- Quality Level (1588 PTP) 329
- Quality Level (SyncE) 331
- NetBlazer 323 333
- Loopback 334
- Frame Delay 335
- Frame Loss 336
- Synthetic Loss 337
- Service Name and Selection 338
- Committed/Excess 338
- Committed/Excess Steps 339
- Service Performance 340
- RX Frame Count 341
- Streams - Jitter 342
- Streams - Latency 343
- Streams - Throughput 344
- Summary 345
- Traffic / Traffic Ethernet 348
- Summary (1588 PTP) 349
- NetBlazer 341 351
- Delay Measurement 352
- Total PTP Messages 352
- Summary (Cable Test) 353
- 346 FTB-700G/800 Series 356
- Summary (EtherSAM) 357
- Start Time 358
- NetBlazer 349 359
- Summary (FC BERT) 360
- Summary (ISDN PRI) 362
- NetBlazer 353 363
- Performance 365
- Statistics 366
- Summary (NI/CSU Emulation) 368
- Summary (RFC 2544) 369
- Latency Subtests 370
- NetBlazer 361 371
- Summary (S-OAM) 372
- NetBlazer 363 373
- Summary (SyncE) 376
- NetBlazer 367 377
- Summary (TCP Throughput) 378
- NetBlazer 369 379
- Ethernet Traffic 380
- Test Status 381
- Traces - OTN 383
- 374 FTB-700G/800 Series 384
- Traces - SONET/SDH 385
- Traffic - Ethernet 386
- Frame Size 387
- Traffic - Flow Control 388
- Pause Injection 389
- Traffic - Graph 390
- Traffic - S-OAM 391
- 382 FTB-700G/800 Series 392
- Traces/Label 393
- 10 Test Functions 395
- Test Functions 396
- NetBlazer 389 399
- FDL - Bit-Oriented Message 402
- 394 FTB-700G/800 Series 404
- Receive Messages 406
- Command/Response 407
- Generated Messages 408
- Received Messages 409
- Channel 413
- Channel Codeword 413
- Loopback Commands 415
- Filters 416
- Enabled Time 416
- Assign to Capture 417
- Filter Configuration 417
- 408 FTB-700G/800 Series 418
- Category Filter 418
- Filter Statistics 419
- Capture Source 420
- Frame Length 421
- Status and Controls 423
- Generate & Save 425
- OH - OTN 426
- NetBlazer 417 427
- NetBlazer 419 429
- OH - SONET/SDH 432
- Transport OH - Section/RS 433
- Transport OH - Line/MS 434
- NetBlazer 427 437
- STS/AU/TU-3 439
- NetBlazer 431 441
- NetBlazer 433 443
- 434 FTB-700G/800 Series 444
- Default all OH 445
- Ping & Trace Route 446
- NetBlazer 437 447
- Trace Route 448
- Status Description 449
- Pointer Adjustment 451
- 444 FTB-700G/800 Series 454
- Description 455
- 446 FTB-700G/800 Series 456
- 448 FTB-700G/800 Series 458
- RX Pointer Adjustment 462
- 454 FTB-700G/800 Series 464
- Measure Delay Button 465
- S-OAM Link Trace 467
- 458 FTB-700G/800 Series 468
- Signaling Bits 469
- Spare Bits 470
- NetBlazer 461 471
- 11 Test Control 473
- Discover Remote Button 474
- Local Module Identification 476
- Headset/DTMF Button 477
- 468 FTB-700G/800 Series 478
- Laser Button 479
- 470 FTB-700G/800 Series 480
- Loopback Tool tab 481
- NetBlazer 473 483
- Interface Tab 484
- NetBlazer 475 485
- Network tab 486
- SFP/SFP+ tab 486
- Phone Book Button 487
- Save/Load tab 488
- Import/Export tab 490
- Report Button 491
- Open Tab 493
- Import/Export Tab 494
- Reset Button 495
- Save/Load Button 496
- 488 FTB-700G/800 Series 498
- Start/Stop Button 502
- 12 Power Failure Recovery 503
- When Using the Test Timer 504
- 13 Suspend and Resume 505
- Resume Operation 506
- 14 Maintenance 507
- Cleaning LC Connectors 508
- Recalibrating the Unit 509
- Recycling and Disposal 510
- 15 Troubleshooting 511
- Transportation 512
- 16 Warranty 513
- Service and Repairs 515
- 506 FTB-700G/800 Series 516
- 17 Specifications 517
- Specifications 518
- Interfaces 519
- SFP Fibre Channel Interfaces 525
- SFP+ Fibre Channel Interfaces 526
- Synchronization Interface 527
- 18 Glossary 529
- 520 FTB-700G/800 Series 530
- Acronym List 530
- 522 FTB-700G/800 Series 532
- 524 FTB-700G/800 Series 534
- 526 FTB-700G/800 Series 536
- 528 FTB-700G/800 Series 538
- 530 FTB-700G/800 Series 540
- 532 FTB-700G/800 Series 542
- 534 FTB-700G/800 Series 544
- 10G Ethernet Client 545
- Glossary 546
- NetBlazer 539 549
- 1588 PTP Profiles 550
- 542 FTB-700G/800 Series 552
- Ethernet Cables 553
- Crossover Cable (1000 Mbit/s) 554
- 546 FTB-700G/800 Series 556
- NetBlazer 547 557
- NetBlazer 549 559
- 550 FTB-700G/800 Series 560
- Framing 560
- OTU FEC 560
- Overhead 561
- 552 FTB-700G/800 Series 562
- Optical Data Unit (ODU) 563
- 554 FTB-700G/800 Series 564
- Optical Payload Unit (OPU) 564
- NetBlazer 555 565
- Tandem Connection Monitoring 565
- 556 FTB-700G/800 Series 566
- NetBlazer 557 567
- Forward Error Correction 567
- ODU Multiplexing 568
- NetBlazer 559 569
- ODUflex 570
- MPLS Labels 571
- SONET/SDH 572
- Nomenclature 573
- 564 FTB-700G/800 Series 574
- Layer SONET SDH 574
- SONET Numbering Convention 576
- SDH Numbering Convention 577
- 4 respectively 579
- 570 FTB-700G/800 Series 580
- DSn/PDH Numbering Convention 581
- 572 FTB-700G/800 Series 582
- NetBlazer 573 583
- VLAN ID and Priority 585
- NetBlazer 577 587
- NetBlazer 579 589
- NetBlazer 581 591
- NetBlazer 583 593
- NetBlazer 585 595
- NetBlazer 587 597
- NetBlazer 589 599
- NetBlazer 591 601
- NetBlazer 593 603
- NetBlazer 595 605
- NetBlazer 597 607
- NetBlazer 599 609
- NetBlazer 601 611
- NetBlazer 603 613
- NetBlazer 605 615
- NetBlazer 607 617
- ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ 619
- MARKING REQUIREMENTS 620
Relacionado con productos y manuales para Instrumentos de medición Exfo FTB-800 Series for FTB-1
Instrumentos de medición Exfo FTB-8100 Series Transport Blazer for FTB-200 Manual de usuario
(518 paginas)
(518 paginas)
Instrumentos de medición Exfo FTB-8100 Series Transport Blazer for FTB-500 Manual de usuario
(719 paginas)
(719 paginas)
(574 paginas)
Instrumentos de medición Exfo FTB/IQS-85100G Packet Blazer for FTB-500/IQS-600 Manual de usuario
(448 paginas)
(448 paginas)
Instrumentos de medición Exfo FTB/IQS-88000 Series Power Blazer for FTB-2/2Pro/5 Manual de usuario
(681 paginas)
(681 paginas)
Instrumentos de medición Exfo FastReporter Data Post-Processing Software Manual de usuario
(256 paginas)
(256 paginas)
Instrumentos de medición Exfo FastReporter Data Post-Processing Software Manual de usuario
(270 paginas)
(270 paginas)
(274 paginas)
(47 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales