Exfo FTB-610 Wideband Copper Test Module Manual de usuario Pagina 191
- Pagina / 326
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Multimeter 2 Tests
Copper Test 183
Station Ground
The page displays the Station Ground pass/fail results and the following
measurement values:
Line Card Type displays one of the following messages:
Card Not Detected
Voltage Source
Current Source
Line Card Voltage Polarity displays either Ok or Reversed.
Station Voltage is the maximum/minimum AC/DC threshold voltage
value for the circuit.
Loop Current is the minimum loop current for the circuit in mA.
Loop Resistance displays the resistance value of the twisted cable
pair.
Station Ground Resistance from 0.0 to 25.0 ohms is considered a
pass.
If an error message is displayed in lieu of the resistance measurement, one
of the following conditions could exist:
Loop resistance > 10 k Ohms
Tip (A) not connected to Ground (Earth) at CO
Improper hookup (check your lead connections)
Incorrect/no line card
Improper line voltage, polarity, or current
Resistance measurement error (out of range for normal resistance
measurement, etc.).
- User Guide 1
- Copyright Information 2
- Contents 3
- Copper Test v 5
- Certification Information 7
- 1 Introducing the FTB-610 9
- Advanced WB Copper Test 9
- Typical Applications 10
- Software Options 11
- IMPORTANT 12
- 2 Safety Information 13
- Electrical Safety Information 14
- Equipment Ratings 15
- 3 Getting Started 17
- Cable Connections 18
- 12 FTB-610 20
- Getting Started 21
- 14 FTB-610 22
- Copper Test 15 23
- Turn screws 23
- Back panel 23
- Copper Test 17 25
- Usual Tab Elements 26
- Graph Controls 27
- 4 Advanced WB Copper 29
- Application 29
- Status Bar 30
- Title Bar 31
- Test Information and Control 31
- Main Menu 31
- Application buttons 32
- Exit Button 34
- Start/Stop Button 35
- Cable Book 36
- Load Cable 37
- Cable Details 38
- Copper Test 31 39
- Add Cable 40
- Copper Test 33 41
- Clone Cable 42
- Delete Cable 43
- Phone Book 44
- Load Group/Entry 45
- Phone Book Details 46
- Copper Test 39 47
- Add Group 48
- Clone Group 49
- Delete Group 50
- Load Phone Book 51
- Save Phone Book 52
- Copper Test 45 53
- 46 FTB-610 54
- Enter Number 55
- Recent Dialed Numbers 56
- Select from Phone Book 56
- Add to Phone Book 57
- Config/Profile 58
- Profile Details 60
- Copper Test 53 61
- 54 FTB-610 62
- Auto Test Profile Details 63
- 56 FTB-610 64
- Copper Test 57 65
- 58 FTB-610 66
- Isolation 66
- Station Ground 66
- TDR Test Profile Details 67
- Signal Test Profile Details 68
- Noise Test Profile Details 69
- Impulse Test Profile Details 70
- Copy from USB 71
- Copy to USB 71
- Delete Profile 72
- Application Settings 74
- Copper Test 67 75
- Standard 76
- Ω/km or Ω/mi) 77
- Identification 78
- File Name 79
- 72 FTB-610 80
- Factory Default 81
- Save Test 82
- Copper Test 75 83
- Select Result File 85
- Select Report File 86
- Result File 87
- Reading the Result File 88
- Result Summary 90
- Copper Test 83 91
- Export Results 95
- 7 Pair Detective Test 97
- Setting Threshold Values 100
- Edit Messages 101
- Setting Cable Parameters 102
- Copper Test 95 103
- Multimeter 104
- Copper Test 97 105
- 98 FTB-610 106
- 8Auto Test 107
- Setting Test Volume 110
- Setting Test Parameters 111
- Summary 112
- User Auto Test 113
- User Auto Test Selection 114
- Copper Test 107 115
- Multimeter 1 116
- Multimeter 2 117
- 110 FTB-610 118
- Copper Test 111 119
- 9 FaultMapper Test 123
- Copper Test 119 127
- 120 FTB-610 128
- FaultMapper Test 129
- 10 Multimeter Tests 131
- Multimeter Main Page 132
- Voltage Test 133
- Continuous AC 135
- Continuous DC 137
- Multimeter Tests 141
- Current Test 142
- Copper Test 135 143
- Copper Test 137 145
- Copper Test 139 147
- Resistance Test 151
- Continuous 153
- Capacitance/Opens Test 158
- Copper Test 151 159
- Copper Test 153 161
- Resistive Balance Test 165
- 158 FTB-610 166
- 160 FTB-610 168
- Balance Test 169
- 164 FTB-610 172
- 166 FTB-610 174
- 168 FTB-610 176
- 11 Multimeter 2 Tests 177
- Isolation Test 178
- Copper Test 171 179
- Locator Tone Test 184
- 178 FTB-610 186
- Load Coils Test 187
- Copper Test 181 189
- Station Ground 190
- Copper Test 183 191
- Hookup Diagram 192
- 186 FTB-610 194
- 12 TDR Test 195
- Auto TDR 196
- Edit Parameters 197
- Select Cable 198
- Manual TDR 199
- Trace Setup 202
- Copper Test 195 203
- Save/Load Trace(s) 204
- Copper Test 197 205
- Trace Result File 206
- Xtalk TDR 207
- 202 FTB-610 210
- 13 RFL Test 211
- 204 FTB-610 212
- RFL-2-Wire 212
- Copper Test 205 213
- RFL-4-Wire 214
- Copper Test 207 215
- RFL-K-Test 217
- Copper Test 211 219
- Copper Test 213 221
- Supplemental 222
- 14 Signal Test 223
- WB Balance Test 224
- WB Balance 225
- Copper Test 219 227
- WB Attenuation Test 230
- Copper Test 223 231
- Copper Test 227 235
- TX/RX Tone Test 236
- Receive Tone 239
- 232 FTB-610 240
- 15 Noise Tests 243
- VF Noise Test 244
- Copper Test 237 245
- 240 FTB-610 248
- Power Influence Test 249
- 242 FTB-610 250
- Test Parameters 252
- WB PSD Noise Test 254
- Copper Test 247 255
- General Settings 257
- Enable Disturbers 258
- Enable Masks 259
- Copper Test 255 263
- Setting Spot Test Parameters 265
- Setting Spot Test Thresholds 266
- Spectrum 267
- Ωor 135 Ω 268
- Copper Test 261 269
- Noise Tests 270
- 16 Impulse Tests 271
- Impulse Tests 272
- To start/stop a test: 272
- VF Impulse Noise Test 273
- WB Impulse Noise Test 277
- 270 FTB-610 278
- WB Histogram 282
- Impulse Scope Test 283
- 278 FTB-610 286
- Graph Settings 288
- Copper Test 281 289
- Impulse Duration 290
- Disruption 292
- 17 Test Lead Compensation 297
- 290 FTB-610 298
- Copper Test 291 299
- 19 Maintenance 301
- Recalibrating the Unit 302
- Recycling and Disposal 303
- 20 Troubleshooting 305
- 298 FTB-610 306
- Solving Common Problems 306
- Select any of the user 306
- User the up/down 306
- Copper Test 299 307
- Transportation 308
- 21 Warranty 309
- Liability 310
- Service and Repairs 312
- Copper Test 305 313
- A Technical Specifications 315
- Technical Specifications 316
- 310 FTB-610 318
- Copper Test 311 319
- Copper Test 313 321
- Copper Test 315 323
- ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ 324
- MARKING REQUIREMENTS 325
Relacionado con productos y manuales para Instrumentos de medición Exfo FTB-610 Wideband Copper Test Module
(352 paginas)
Instrumentos de medición Exfo FTB-635 Wideband Copper and DSL Test Module Manual de usuario
(373 paginas)
(373 paginas)
Instrumentos de medición Exfo FTB-635 Wideband Copper and DSL Test Module Manual de usuario
(408 paginas)
(408 paginas)
Instrumentos de medición Exfo FTB-635 Wideband Copper and DSL Test Module Manual de usuario
(427 paginas)
(427 paginas)
(366 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales