Exfo FTB-8500 Series for FTB-200 Manual de usuario Pagina 32
- Pagina / 513
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Physical Interfaces and LEDs
18 FTB-8500 Series and FTB-8120NGE/8130NGE
FTB-8525 and FTB-8535 Models
Electrical 10/100/1000 Mbps Ethernet
The FTB-8525/FTB-8535 module provides one electrical port for 10Base-T,
100Base-T, or 1000Base-T.
Port connector type is RJ-45 for category 5 unshielded twisted pair (UTP)
connection.
Note: Refer to Specifications on page 411 for cable specifications.
Connect the 10/100/1000 electrical signal to be tested to the port
ETHERNET 10/100/1000.
LEDs
LED Status Description
LINK/ACT
(Green)
On Ethernet link up.
Off Ethernet link down.
Flashing TX/RX activity.
DUPLEX
(Yellow)
On Full Duplex mode.
Off Half Duplex mode.
Flashing Collisions are detected.
- Ethernet and 1
- Fibre Channel Application 1
- Contents 3
- Certification Information 9
- CE Declaration of Conformity 11
- DECLARATION OF CONFORMITY 12
- IMPORTANT 17
- 2 Safety Information 19
- 3 Getting Started 23
- FTB-8510B Model 25
- LED Status Description 26
- 1x/2x Fibre Channel 27
- LEDs for Optical Ports 28
- FTB-8510G Model 29
- FTB-8525 and FTB-8535 Models 31
- Ethernet 100/1000 Mbps 33
- 1x/2x/4x Fibre Channel 41
- 5 Introducing the Smart User 47
- Main Window 49
- Main Menu 50
- Print Screen 52
- Global Test Status 55
- Test Controls 56
- Button Description 57
- Favorites 58
- Factory Default 59
- Test Report Generation 60
- Configuration 64
- Typical Tab Elements 67
- Alarm/Error Measurements 68
- Arrow Buttons 68
- Table Sorting 69
- Port Selection 69
- Keyboard Usage 70
- (0 through 9 and A through F) 73
- For MAC address 73
- For IPv6 address 73
- 6 Creating and Starting a 77
- Test Case 77
- Introducing the Test Setup 78
- Available with 79
- Test Case Availability 80
- EtherSAM (Y.1564) Test Case 81
- Test Set Test Cases 87
- IPv4 IPv6 92
- Ethernet RFC 2544 Test Case 95
- Ethernet BERT Test Case 100
- Fibre Channel BERT Test Case 118
- 7 Summary Tabs 123
- Test Status 124
- Test Configuration 126
- Clock Configuration 127
- Timer Configuration 128
- Alarm Analysis 129
- Alarm Summary 130
- for all interfaces 131
- Test Preferences 133
- Test Logger 134
- Logger Table 135
- Test L ogger 136
- View/Hide Details 137
- Log Details 138
- 8 I/F Setup Tabs 139
- Port Setup 140
- Flow Control 141
- Network Setup 143
- IP Configuration 144
- Advanced Auto-Neg. TX 146
- Configuration 147
- Auto-Neg. Fault Register 149
- Enable Local Capabilities 149
- Local Capabilities 149
- Negotiate Button 150
- Advanced Auto-Neg. RX 151
- Apply to Port Configuration 152
- Link Partner Capabilities 152
- Interface 153
- Buffer-to-Buffer Flow Control 156
- World Wide Name 156
- 9Port Tabs 157
- Electrical TX 158
- Frequency 159
- Electrical RX 160
- Frequency Analysis 161
- Optical TX 162
- Optical RX 164
- 10 WIS Tabs 167
- Alarm Generation 168
- Error Injection 169
- Path Signal Label (C2) 170
- J0 Trace 170
- J1 Trace 170
- Error Analysis 171
- WIS OH RX 174
- Section Overhead 175
- Line Overhead 175
- Path Overhead 176
- 11 Traffic Analyzer Tabs 177
- Ethernet TX 178
- PHY Error Injection 179
- MAC Error Injection 179
- Ethernet RX 181
- Errors Analysis 182
- Ethernet Statistics 184
- Valid Frame Counts 185
- Frame Size 186
- Throughput 186
- Valid PBB-TE Frame Counts 187
- PPB-TE Frame Size 188
- PBB-TE RX Throughput 188
- Higher Layers 189
- Flow Control 191
- Destination MAC Address 192
- Statistics 193
- Traffic Filters 194
- Enabled Time 195
- Frame Count 195
- Traffic Filter Configuration 196
- Filter Configuration 198
- Configure Button 199
- Category Filter Comment 200
- Frame Length 204
- Status and Controls 206
- Traffic Analyzer Tabs 208
- FC Error Injection 211
- FC Latency 214
- Latency Measurements 215
- Buffer-to-Buffer Credit 215
- FC Statistics 216
- 12 Stream Generation Tabs 217
- Overview 218
- FTB-8510G 221
- Component Description 224
- Stream Configuration 225
- Frame Configuration 226
- Traffic Shaping 231
- Stream No 234
- Destination 235
- Frame Format 236
- MPLS Configuration 240
- IP/UDP/TCP 241
- Frame Delimiters 245
- EOF Description 246
- Frame Parameter 247
- FC Header 248
- D_ID Description 249
- Bit Field Description 251
- 2 Exchange 252
- 13 Stream Analyzer Tabs 255
- RX Frame Count 257
- Stream Errors Analysis 257
- Round Trip Latency 258
- 14 Pattern Tabs 259
- Pattern TX 260
- Pattern RX 263
- 15 RFC 2544 Tabs 265
- Global Configuration 266
- Test Procedure 268
- Latency Measurement 269
- Throughput Configuration 270
- Back-to-Back Configuration 273
- Frame Loss Configuration 275
- Latency Configuration 277
- Throughput Results 280
- Back-to-Back Results 282
- Frame Loss Results 284
- Latency Results 286
- 16 EtherSAM Tabs 293
- Overview (Configuration) 294
- Burst Test 296
- Performance Test 296
- Sub-Tests Duration 297
- Total TX Rate (%) 298
- Services (Configuration) 299
- Direction 300
- Frame Parameters 300
- SLA Parameters 301
- Test Parameters 304
- Ramp (Configuration) 305
- Step List 306
- Step Time 306
- Ramp Duration 306
- Burst (Configuration) 307
- Parameters 308
- Global Progress and Alarms 310
- Configuration Test Overview 312
- Performance Test Overview 314
- Configuration Test (Results) 316
- Ramp and Burst Tests Table 317
- Performance Test (Results) 319
- Sequence Tracking 320
- One-Way Latency 321
- 17 TCP Throughput Tabs 323
- TCP Mode 324
- TCP Connection Configuration 324
- TCP Connection Status 325
- TCP Throughput Configuration 326
- TCP Throughput Results 327
- TCP Statistics 328
- 18 Advanced Tab 329
- Service Disruption Time (SDT) 332
- 19 Common Tab 333
- Standard 334
- Performance Monitoring (PM) 336
- 20 Expert Mode Tabs 337
- Expert Mode (RFC 2544) 338
- Expert Mode Status 339
- Throughput (RFC 2544) 340
- Back-to-Back (RFC 2544) 342
- Frame Loss (RFC 2544) 344
- Latency (RFC 2544) 346
- Expert Mode (BERT) 348
- Port (BERT) 349
- Ethernet (BERT) 351
- Pattern (BERT) 353
- 21 System Tabs 355
- Application Preferences 356
- Audible Error/Alarm 357
- FTB-8120NGE/FTB-8130NGE 358
- FTB-8510B 358
- Interface Configuration 359
- IPv6 Test Preferences 361
- FC Test Preferences 364
- Versions 366
- Information 367
- Software Options 369
- Available Options 370
- Category Name Description 371
- Clock Synchronization 374
- Clock Out 377
- 22 Tools Tabs 379
- IPv6IPv4 381
- Trace Route 386
- Status Description 388
- ENIU Configuration 390
- ADC Configuration 391
- Selected ENIU 393
- Loopback 394
- 802.3ah Configuration 395
- OAM Discovery Statistics 397
- 802.3ah Statistics 398
- 802.3ah Events 401
- Traffic Scan 403
- Mode Level Description 404
- Monitored Frames Table 406
- Tools Tabs 407
- Filter Cfg 409
- 23 Suspend and Resume 411
- Resume Operation 412
- 24 Power Failure Recovery 413
- When Using SmartMode 414
- 25 Maintenance 415
- Recalibrating the Unit 416
- Recycling and Disposal 416
- 26 Troubleshooting 417
- Transportation 418
- 27 Warranty 419
- Liability 420
- Service and Repairs 422
- ASpecifications 425
- Ethernet Optical Interfaces 426
- Fibre Channel Interfaces 428
- ELECTRICAL INTERFACES 430
- Ethernet Cables 431
- Specifications 432
- Crossover Cable (1000 Mbps) 432
- Synchronization Interfaces 433
- B Glossary 435
- Acronym List 436
- VLAN/B-VLAN 448
- MPLS Labels 449
- Path Signal Label (C2 byte) 450
- C Pop-Up Windows 451
- VLAN Configuration 452
- B-MAC Destination Address: 453
- IPv4 Configuration 455
- IPv6 Address Configuration 457
- Global IPv6 Address 458
- Mode Status Description 459
- Default Gateway Address 460
- Destination IPv6 Address 461
- Service Profile Configuration 463
- Framing Configuration 464
- Frame Size Configuration 465
- Frame Format Configuration 467
- MAC Configuration 468
- UDP Configuration 470
- TCP Configuration 470
- Advanced TOS/DS 471
- Advanced Ping 474
- Advanced Trace Route 476
- Filter Selection 477
- Truncation Calculator 478
- Field Match Configuration 479
- Triggered Frame Details 481
- Data Capture Export 482
- D Report Generator 485
- Report Generator Installation 486
- Model Application Folder 488
- Error message 490
- Sections 492
- View Report After Generation 493
- Default Button 493
- Generate Button 493
- Close Button 493
- 147, 151 503
- I/F Setup37 508
- ₼⦌␂ℝ☀⹂䓸德棟Ⓟ䤓屓⸩ 511
- MARKING REQUIREMENTS 512
Relacionado con productos y manuales para Instrumentos de medición Exfo FTB-8500 Series for FTB-200
(574 paginas)
Instrumentos de medición Exfo FTB/IQS-85100G Packet Blazer for FTB-500/IQS-600 Manual de usuario
(448 paginas)
(448 paginas)
Instrumentos de medición Exfo FTB/IQS-88000 Series Power Blazer for FTB-2/2Pro/5 Manual de usuario
(681 paginas)
(681 paginas)
Instrumentos de medición Exfo FastReporter Data Post-Processing Software Manual de usuario
(256 paginas)
(256 paginas)
Instrumentos de medición Exfo FastReporter Data Post-Processing Software Manual de usuario
(270 paginas)
(270 paginas)
Instrumentos de medición Exfo FastReporter Data Post-Processing Software Manual de usuario
(274 paginas)
(274 paginas)
(47 paginas)
Instrumentos de medición Exfo MAX-700 Manual de usuario
(381 paginas)
(381 paginas)
Instrumentos de medición Exfo MAX-700 Manual de usuario
(418 paginas)
(418 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.070 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales