Exfo MaxTester MAX-610 Manual de usuario Pagina 224
- Pagina / 281
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
RFL
216 MAX-610
Separate Good Pair
Note: Results are more accurate but less forgiving than a 2-wire setup because
the 4-wire setup requires you to connect the faulted wire conductor to the
Ring (red) jack only.
Current Test displays the test being measured. When FED is Enabled,
the FED icon and numeric state are displayed beside the Current Test.
Cable Setup button opens a new page that allows you to set the cable
parameters for the Current Test. Press to open the page.
Result displays the separate good pair RFL test results. Based on the
cable condition, corresponding values are added into the diagram at
their specific positions. Test result units are dependent on Standard in
Setup/Application Settings.
Distance to strap (DTS).
Resistance to strap (RTS).
Distance from fault to strap (DFTS).
Resistance from fault to strap (RFTS).
Resistance to fault (RTF).
Distance to fault (DTF).
Faulted cable (FC).
Resistance at fault (Rf) is resistance from the fault to the resistance
wire.
Voltage at fault (Vf).
If the test reports that it cannot detect the strap when the measured
loop resistance is >10 k Ohm, this may mean:
There is no strap connected.
There is a strap, but the cable is too long and has a loop resistance
>10 k Ohm.
- MaxTester MAX-610 1
- Copyright Information 2
- Contents 3
- MaxTester Copper Test v 5
- Certification Information 7
- DECLARATION OF CONFORMITY 8
- 1 Introducing the MaxTester 9
- Typical Applications 10
- Using the MAX-610 10
- 4 MAX-610 12
- Cable Connections 13
- 6 MAX-610 14
- IMPORTANT 16
- Electrical Safety Information 18
- Equipment Ratings 19
- 3 Getting Started with the 21
- MaxTester 21
- Using Menus and Keypad 22
- Using Online Help 23
- 4 Setting Up the MaxTester 25
- System Settings 26
- Display and Language 27
- Date and Time 28
- Battery Status 29
- Power Schemes 29
- Calibration 30
- MaxTester Copper Test 23 31
- Software Options 32
- Information 33
- Upload Setup 34
- FTP Setup 36
- Wi-Fi Setup 37
- 30 MAX-610 38
- Select Network 39
- Ethernet Setup 40
- MaxTester Copper Test 33 41
- 5 Setting Up Copper Tests 43
- Test Configuration 44
- MaxTester Copper Test 37 45
- Select Profile 46
- Profile Details Main Menu 47
- Multimeter Profile Details 47
- Noise Tests Profile Details 48
- Auto Test Profile Details 49
- Delete Profile 50
- MaxTester Copper Test 43 51
- Select Group/Entry 53
- Phone Book Details 53
- Add Group 55
- Clone Group 56
- Delete Group 57
- Load Phone Book 58
- Save Phone Book 59
- Dialer Function 60
- MaxTester Copper Test 53 61
- Enter Number 62
- Recent Dialed Numbers 63
- Select from Phone Book 63
- Add to Phone Book 64
- Cable Book 65
- Cable Details 66
- Add Cable 67
- Clone Cable 69
- Delete Cable 70
- Application Settings 71
- Ω/km or Ω/mi) 73
- Identification 75
- Test List Setup 76
- File Name 77
- Change Order 78
- Test Lead Compensation 80
- FED Setup 81
- 74 MAX-610 82
- MaxTester Copper Test 75 83
- Frequency 86
- Saving Results 87
- Select Result File 89
- 6 Reading Saved Copper Test 91
- Read Result Menu 92
- MaxTester Copper Test 85 93
- FED Details 96
- MaxTester Copper Test 89 97
- to come out of the list 97
- MaxTester Copper Test 91 99
- 7 Multimeter Tests 101
- Snapshot 102
- Voltage Thresholds 103
- Continuous AC Page 104
- Continuous DC Page 105
- 98 MAX-610 106
- Ω that defines how 107
- Current Thresholds 108
- MaxTester Copper Test 103 111
- Resistance 112
- Resistance Thresholds 113
- Continuous 114
- Ω and %. Parameters are as 115
- Ω and % 116
- Isolation 118
- Isolation Thresholds 119
- Capacitance/Opens 122
- Station Ground 126
- Threshold Settings 128
- Result Details 128
- Stressed Balance 129
- 8 SmartR™ Features 133
- 126 MAX-610 134
- Pair Detective 134
- Pair Detective Cable Setup 135
- Multimeter 137
- MaxTester Copper Test 131 139
- Cable Setup 140
- Pair Detective Result Details 141
- FaultMapper 143
- MaxTester Copper Test 137 145
- FaultMapper Result Details 146
- Result Details Cable Setup 147
- FaultMapper Profile Details 148
- 9 Noise Tests 149
- VF Noise 150
- VF Noise Threshold Settings 151
- Power Influence 153
- VF Impulse Noise 156
- WB PSD Noise 160
- MaxTester Copper Test 153 161
- WB Impulse Noise 165
- 158 MAX-610 166
- MaxTester Copper Test 159 167
- Profile Details 168
- MaxTester Copper Test 161 169
- MaxTester Copper Test 163 171
- Spot Threshold Settings 172
- Spot Result Details 173
- Spectrum 174
- MaxTester Copper Test 167 175
- Spectrum Threshold Settings 177
- Spectrum Result Details 178
- NEXT Results Profile Details 179
- 10 Frequency Tests 181
- VF/AC Balance 182
- Active Result Details 184
- Passive Result Details 187
- WB Balance 188
- MaxTester Copper Test 181 189
- WB Balance Threshold Settings 191
- WB Attenuation 193
- WB Attenuation Result Details 197
- Load Coils 200
- MaxTester Copper Test 193 201
- Load Coils Result Details 202
- Locator Tone 203
- 196 MAX-610 204
- TX/RX Tone 205
- 198 MAX-610 206
- Receive Tone 207
- Profile Details Receive Tone 208
- MaxTester Copper Test 203 211
- 204 MAX-610 212
- Load Trace 214
- MaxTester Copper Test 209 217
- TDR Profile Details 220
- Single Pair 221
- Separate Good Pair 223
- MaxTester Copper Test 217 225
- RFL Cable Setup 226
- 13 Copper Auto Tests 231
- POTS Auto Test 232
- MaxTester Copper Test 225 233
- Phone Book 235
- User Auto Test 236
- Test Selection 237
- Upload/Save Result 240
- MaxTester Copper Test 233 241
- Multimeter 1 Result 242
- Multimeter 2 Result 243
- Noise Result1 243
- Noise Result2 244
- Frequency Result 245
- TDR Result 245
- TDR Result Cable Setup 247
- Test Parameters 251
- Multimeter Parameter 251
- Noise 1 Parameter 251
- Noise 2 Parameter 252
- Frequency Parameter 252
- TDR Parameter 252
- Test Thresholds 253
- Multimeter 1 Threshold 253
- Multimeter 2 Threshold 253
- Noise Threshold 254
- Frequency Threshold 254
- 14 Maintenance 255
- Recalibrating the Unit 256
- 250 MAX-610 258
- Battery Calibration 259
- Unit Temperature Handling 259
- Replacing the Battery 259
- Recycling and Disposal 260
- 15 Troubleshooting 261
- Troubleshooting 262
- Turn the unit on again to 262
- LED Statuses 263
- 256 MAX-610 264
- Transportation 265
- Liability 268
- Service and Repairs 270
- MaxTester Copper Test 263 271
- A Technical Specifications 273
- Technical Specifications 274
- COPPER SPECIFICATIONS 275
- (continued) 275
- GENERAL SPECIFICATIONS 276
- MaxTester Copper Test 269 277
- MARKING REQUIREMENTS 280
Relacionado con productos y manuales para Instrumentos de medición Exfo MaxTester MAX-610
Instrumentos de medición Exfo OTDR 2 Manual de usuario
(209 paginas)
(209 paginas)
Instrumentos de medición Exfo OTDR 2 Manual de usuario
(208 paginas)
(208 paginas)
Instrumentos de medición Exfo OTDR 2 Manual de usuario
(211 paginas)
(211 paginas)
Instrumentos de medición Exfo OTDR 2 Manual de usuario
(207 paginas)
(207 paginas)
Instrumentos de medición Exfo OTDR 2 Manual de usuario
(219 paginas)
(219 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales